横向扰动对超声速混合层被动标量混合影响分析

采用大涡模拟数值计算二维空间发展的超声速混合层,重点分析横向扰动对混合层的标量结构、标量厚度以及标量体积卷吸率的影响。采用理论模型验证了数值方法在计算标量混合特性方面的准确性。结果表明,横向扰动频率和振幅明显影响着混合层的标量增长率和卷吸率。高频扰动增大了混合层近场标量增长率和卷吸率,但是低频扰动改善了混合层远场标量增长率。大尺度涡卷吸过程对混合层标量卷吸率起决定作用。多频扰动有效地增强了超声速混合层的标量混合。     

基于BP神经网络的闭路制导改进方法

针对传统闭路制导方法中的制导方法误差,提出了一种根据"真实目标"进行制导的改进制导方法。采用BP神经网络逼近算法,推导建立预定关机点及落点坐标与需要速度间的映射关系,并装订上弹,使关机点附近对应每一个位置能够映射出相应的需要速度矢量。然后利用闭路制导关机及导引方法对导弹实施控制。通过仿真,该方法大大减小了制导方法误差,提高了导弹射击精度。     

函数变换提高灰色预测模型精度的条件

指出选择函数变换来提高模型精度主要与三个方面的因素有关：提高数据序列的光滑比、调整数据序列的级比和确保凸凹性。在调整级比方面，扩充了级比压缩变换的相关定理，并讨论了几种常用的函数变换在上述三个方面的关系。最后结合实例提出，对于变换后的数据序列若不满足这三方面的要求可以再进行函数变换以达到提高模型精度的目的。     

连续旋转爆震波传播模态试验

通过保持空气流量不变、改变H2/air当量比开展了连续旋转爆震对比试验,发现随当量比的降低出现三种传播模态:在较高的当量比(0.90~1.86)下,连续旋转爆震波以同向传播模态传播;在较低的当量比(≈0.75)下,则以双波对撞模态传播;在中间工况,则以上述混合模态维持传播。分析了不同传播模态下的高频压力特征,并初步分析了传播模态的转换机制:当量比较高时,爆震强度较高,传播过程中的损失和速度亏损相对较小,爆震波以同向传播模态维持传播;当量比较低时,爆震强度较低,传播过程中的损失和速度亏损较大,此时无法维持同向传播模态,而以双波对撞模态传播,这是由于双波对撞模态中的激波对撞产生高温环境,有利于燃烧放热,其可能是连续旋转爆震的极限传播模态。     

基于圆形滤波器HOG特征的航拍图像车辆快速检测算法

航拍图像中车辆一般近似为矩形结构,因此通过统计检测窗口中的梯度方向直方图并根据梯度主方向估计车辆朝向,然后将检测窗口旋转到相应方向进行分类器判别。车辆检测采用级联boosting分类器和梯度方向直方图特征(HOG,Histograms of Orient Gradient),针对旋转窗口中HOG特征的计算,设计了一种基于圆形滤波器的HOG(Circle Filter based HOG,CFHOG)特征,与传统基于积分直方图的HOG特征提取方法相比,显著提高了旋转窗口中HOG特征的计算效率,此外在计算每个像素的梯度时采用查找表代替梯度向量的求模和角度计算也减小了计算量。使用真实图像进行的实验表明本文车辆检测算法快速高效。     

Driving force coordinated control of an 8 ×8 in-wheel motor drive vehicle with tire-road friction coefficient identification

Because of the complexities of tire-road interaction,the wheels of a multi-wheel distributed electric drive vehicle can easily slip under certain working conditions.As wheel slip affects the dynamic per-formance and stability of the vehicle,it is crucial to control it and coordinate the driving force.With this aim,this paper presents a driving force coordination control strategy with road identification for eight-wheeled electric vehicles equipped with an in-wheel motor for each wheel.In the proposed control strategy,the road identification module estimates tire-road forces using an unscented Kalman filter al-gorithm and recognizes the road adhesion coefficient by employing the recursive least-square method.According to road identification,the optimal slip ratio under the current driving condition is obtained,and a controller based on sliding mode control with a conditional integrator uses this value for accel-eration slip regulation.The anti-slip controller obtains the adjusting torque,which is integrated with the driver-command-based feedforward control torque to implement driving force coordination control.The results of hardware-in-loop simulation show that this control strategy can accurately estimate tire-road forces as well as the friction coefficient,and thus,can effectively fulfill the purpose of driving force coordinated control under different driving conditions.     

Optimization of process parameters of the activated tungsten inert gas welding for aspect ratio of UNS S32205 duplex stainless steel welds

The activated TIG (ATIG) welding process mainly focuses on increasing the depth of penetration and the reduction in the width of weld bead has not been paid much attention. The shape of a weld in terms of its width-to-depth ratio known as aspect ratio has a marked influence on its solidification cracking tendency. The major influencing ATIG welding parameters, such as electrode gap, travel speed, current and voltage, that aid in controlling the aspect ratio of DSS joints, must be optimized to obtain desirable aspect ratio for DSS joints. Hence in this study, the above parameters of ATIG welding for aspect ratio of ASTM/UNS S32205 DSS welds are optimized by using Taguchi orthogonal array (OA) experimental design and other statistical tools such as Analysis of Variance (ANOVA) and Pooled ANOVA techniques. The optimum process parameters are found to be 1 mm electrode gap, 130 mm/min travel speed, 140 A current and 12 V voltage. The aspect ratio and the ferrite content for the DSS joints fabricated using the optimized ATIG parameters are found to be well within the acceptable range and there is no macroscopically evident solidification cracking.     

一种鱼雷自导信号频率检测方法研究

靶场在进行智能鱼雷鉴定试验任务时,实时准确地检测出鱼雷自导信号的频率成分是靶标信号处理中的重要环节,谱线比值法便是靶标进行信号处理时检测信号频率的一种有效方法。本文介绍了谱线比值法的基本原理,针对目前鱼雷自导信号特点,对该方法提出了改进方案并进行了仿真。仿真结果表明,经改进的谱线比值法能够满足靶标检测复杂鱼雷自导信号体制下信号频率的使用要求。     

移动式排烟在公路隧道火灾救援中的应用探讨

近年来我国公路隧道的建设迅速发展,然而公路隧道由于空间相对封闭,发生火灾情况下的烟气排除成为了难点。结合公路隧道通风排烟方式,探讨临界风速在隧道火灾排烟时的应用,并分析了公路隧道纵向空气流对火灾烟气流动的影响,指出不同流速的空气流对火灾烟气的影响效果不同,同时阐述了隧道内移动风机的气流环流现象。最后提出了基于不同火灾位置的排烟方案,为消防部队隧道火灾的排烟战术提供参考。     

瞄准式战斗部瞄准策略研究

对不同的瞄准点,瞄准式战斗部对目标毁伤效果不同,为此提出了适用于瞄准式战斗部的瞄准策略,保证了对目标较高的毁伤概率和较好的毁伤效果,解决了起爆之前战斗部的定位问题。